Jump to content

Talk:Bandwidth (signal processing)/Archive 1

Page contents not supported in other languages.
From Wikipedia, the free encyclopedia
Archive 1

Bandwidth vs Throughput

Bandwidth is the frequency, and throughput is actually the Kb/s,Mb/s, etc. If no one disagrees, I will make that change after this discussion posting.

Hmm... I think the term can be used for either. Is that "throughput" before or after encoding? Before or after compression? — Omegatron 19:57, 4 October 2005 (UTC)

Throughput is the amount of data that can be sent over the wire at any particular time. Yes everyone uses the term bandwidth, but it's just not factual. If you are referring to the OSI model with your question, I would think that it would be atleast level 3 or lower, but I am not positive. ymmotrojam 04:40, 12 October 2005 (UTC)

Hi! I do agree that the two terms are not the same though describe related processes. Throughput is indeed the amount of data that can transferred via particular channel. But here is one more confusion regarding the information rate, bandwidth and modulation rate. I would appreciate if anybody read the following:

1. Imagine, the road. The road is your bandwidth. The wider the road the more cars can travel at the same time. One car is a bit of information. So the wider the bandwidth the information bits can bit transferred at a time. We got this one. Cool. Here is one more thing you are to comprise. 2. Assume a road with 4 lines, but we have 2 cars on the garage only! So two lines will be used at a time. Turn on your imagination: a car = a truck with some load. The load is the information we want to transfer. The information rate = the rate of those two trucks. We have more space though! So what we can do is to go to a car rent place to get some more cars. Car rate station is our modulator. Truck is a a carrier we load our information at.We did! Hurray! Now we have to divide the load we are to transfer between 4 cars. As we have 4 lines on the road and 4 trucks the load will be delivered faster as twice as we double our speed. Well, in fact the delivery will be any faster... So when we increase modulation rate.. What I know is that we can adjust signal parameters to recall with particular channel parameters. But how about increase in speed?

Digital bandwidth section

I removed a clause about "with optimal encoding" in the example about a 32-bit data bus. Digital data buses never use a Shannon-Hartley optimal encoding, since that would require reducing the contrast between symbols to account for the high S/N in the bus -- unless the bus S/N ratio is very bad indeed, bilevel binary logic is less than optimal from the standpoint of channel design.

I also removed the phrase "by the uneducated" because it is smarmy and POV. I, too, wish that the bandwidth/capacity channel were not present in common usage, but it is. zowie 01:11, 23 April 2006 (UTC)

bandwidth vs. datarate

I think this mixup of "bandwidth" and "data rate" here is quite bad. Bandwidth in communications is a fixed term measured in Hz - it is related to (but not always 1:1) to the datarate (which you could measure in information/time or Bits/sec).

Yes, the distinction between "bandwidth" and "data rate" can be crucial in some (cascaded) settings, as I have illustrated at...
...to which I would be pleased to see an External Link on this page.Paul Niquette 00:59, 7 December 2006 (UTC)

typo?

English is not my native language, but don't you say "to a great extent" and not "to a great extend"? (in the second to the last paragraph).

Yes, "extend" is the verb, "extent" is the noun.--Orthologist 13:36, 26 February 2007 (UTC)

Declining Bandwidth Costs

Can someone provide a web page or information on the historical decline of bandwidth, say from early '80's through today (perhaps with projections to tomorrow)?

Thank you! R/ Porter Clapp Porter Clapp 19:59, 5 March 2007 (UTC)

To what kind of bandwidth are you referring? Data rate capacity, data count allotments, frequency ranges, or some other definition? And what do you mean by "historical decline"? --JJLatWiki 20:56, 23 May 2007 (UTC)

Confused in "Digital BW"

I can't understand this sentence:"a digital data bus with a bit rate of 66 Mbit/s on each of 32 separate data lines may properly be said to have a bandwidth of 33 MHz and a capacity of 2.1 Gbit/s " It's because how can 66Mbit/s*33MHz=2.1Gbit/s?? It's there any wrong ? In my opinion, the number of bit of each data should be 66 bits and the bandwidth should be 33MHz then the data rate is gonna be 2.1Gbit/s.. If i get wrong concept on this , pls give me the answer~~ Appreciate! Thanks! —Preceding unsigned comment added by Ryan siow (talk • contribs) 02:41, 1 October 2007 (UTC)

The writer meant that 66 Mbit/s can be sent through a band of 33 MHz; true, but utterly irrelevant to the meaning of bandwidth in this context, as your confused interpretation shows. The data rate is 32*66 M = 2.1 Gbps. Dicklyon 02:48, 1 October 2007 (UTC)
Thanks your answer.But i still can't make it clearly. Would u mind tell me what's that mean of "66Mbps"? Thanks! —Preceding unsigned comment added by Ryan siow (talk • contribs) 05:36, 1 October 2007 (UTC)
66 Mbps or Mbit/s is the bit rate on each wire, in megabits per second. Dicklyon 06:16, 1 October 2007 (UTC)

Survey: bit/s/Hz, (bit/s)/Hz or bit·s−1·Hz−1 as Spectral efficiency unit?

Please vote at Talk:Eb/N0#Survey on which unit that should be used at Wikipedia for measuring Spectral efficiency. For a background discussion, see Talk:Spectral_efficiency#Bit/s/Hz and Talk:Eb/N0#Bit/s/Hz. Mange01 (talk) 07:21, 16 April 2008 (UTC)

Proposal: Disambiguation page

There are at least three distinct definitions of bandwidth. The fields in which they are used overlap, so it's easy for people to get confused. I propose making Bandwidth redirect to Bandwidth (disambiguation). That page would have text along the lines of "Bandwidth can mean different things in the related fields of digital networks, communications and signal processing, and linear algebra." It would then go on to describe each in brief (sufficiently to distinguish between the bits/sec and range-of-Hz meanings) with links to the appropriate three articles. As it stands, it seems particularly easy for newbies to not see the difference between bits per second and frequency bands. —Ben FrantzDale (talk) 03:08, 21 March 2008 (UTC)

Actually there would not be a need for a redirect to a Bandwidth (disambiguation) page, the disambiguation page could be directly at Bandwidth (see WP:DAB#NAME, "Generic topic"). The current article would have to be moved to Bandwidth (frequency range) or something like that, and all links to Bandwidth changed to the correct page. -- memset (talk) 16:25, 3 April 2008 (UTC)

Done. There are a lot of links to fix. —Ben FrantzDale (talk) 02:56, 8 April 2008 (UTC)

FYI, I am currently going through the ambiguous links to Bandwidth and changing them to their appropriate sense. This are a lot of them; it will probably take a couple more weeks to get them all done. CosineKitty (talk) 20:00, 22 June 2008 (UTC)
Yea. I've done a handful of them, but there is a lot more to do. A few aren't clear which meaning is appropriate. —Ben FrantzDale (talk) 21:22, 22 June 2008 (UTC)
I know what you mean. A good example is I found a musical album with Bandwidth in the name, and it was linked. There was nothing to distinguish between a range of frequencies or a bit rate, so I left the link to the disambiguation page. We can bounce ideas off of each other here if you want. (I am watching this page.) CosineKitty (talk) 21:42, 22 June 2008 (UTC)

Picture needed

This article really needs a picture in the overview section. Perhaps some kind soul could start with the image in the electromagnetic spectrum article, simplify it, and add some example bandwidths to it (or instruct me how)? --Jhbdel (talk) 07:20, 18 December 2008 (UTC)


Equations

Bandwidth/SNR, or Bitrate/SNR theoretical limits -- anyone know where they are on wikipedia, and why they're not on this page? -- is it called Shannon's theory or something? Ojw 14:53, 18 October 2005 (UTC)

Shannon-HARTLEY Theorem. Yes, it can be found in Wikipedia. —Preceding unsigned comment added by 77.126.65.213 (talk) 07:23, 28 July 2009 (UTC)

First paragraph uses term bandpass without defining it

The first paragraph's last sentence

The term baseband bandwidth always refers to the upper cutoff frequency, regardless of whether the filter is bandpass or low-pass.

is confusing because bandpass is a new term that is not defined or linked

--71.197.3.22 (talk) 20:51, 13 September 2012 (UTC)

I have cleaned up this and other issues in the lead. -—Kvng 00:05, 19 September 2012 (UTC)

Definition of bandwidth

It is not entirely clear to me what "...which are necessarily different for signals than for systems" means. If it really means, as it seems to say, that signal bandwidth is defined differently to system bandwidth, then the following sentence that begins "For example..." does not actually give an example illustrating this. @Dicklyon: who I believe inserted this text. SpinningSpark 16:15, 22 February 2017 (UTC)

"For example, one definition of bandwidth, for a system, could be the range of frequencies over which the system produces a specified level of performance." is an example of a definition of bandwidth of a system. An example of bandwidth of a signal might be good to include there, too. The point is that they are different definitions. E.g., by some definitions, speech signals have a bandwidth of more than 8 kHz, but the phone system has a bandwidth of only 3 kHz, so some of the speech information is lost in phone connections. Dicklyon (talk) 16:41, 22 February 2017 (UTC)
But the current text is not an example of the point of the first sentence. An example would contrast two definitions, not just give one. SpinningSpark 19:38, 22 February 2017 (UTC)

Move discussion in progress

There is a move discussion in progress on Talk:Bandwidth which affects this page. Please participate on that page and not in this talk page section. Thank you. —RMCD bot 19:01, 8 November 2018 (UTC)

Bandwidth in control theory

@Kvng: It appears that in control theory, at least in some contexts, they really do define the bandwidth point as 3 dB below 0 dB. They want to ignore the resonant peak in the closed loop response. See for instance [1], [2], and [3]. SpinningSpark 15:21, 21 February 2019 (UTC)

@Spinningspark: Thanks, I (or anyone else) can look at expanding this description. It needs to include a definition of what 0 dB means. Is the peak reference also used sometimes? Is there a definition for peak? ~Kvng (talk) 15:26, 21 February 2019 (UTC)
I only know what I read in those sources. SpinningSpark 15:30, 21 February 2019 (UTC)

Fractional Bandwidth equation simply wrong

Fractional Bandwidth is the width of the band divided by the center hz of the band. It is demonstrably NOT fHIGH/fLOW.

(fHIGH-fLOW)/fCENTER — Preceding unsigned comment added by 4.4.73.98 (talk) 16:00, 2 October 2020 (UTC)

The bandwidth of wideband circuits is sometimes stated in octaves. This, of course, is log2 of fH/fL. Also for wideband ciruits, the fractional bandwidth centre frequency is taken as the geometric mean of fH and fL rather than the arithmetic mean. For narrowband circuits the difference is insignificant. SpinningSpark 15:13, 5 October 2020 (UTC)
The IP is right that Hi/Lo is not called fractional bandwidth (not even in the cited source). I've clarified this and generally improved the section. SpinningSpark 09:02, 18 October 2020 (UTC)

Graph

It is poor writing style to present a graph with unlabeled axes. I imagine the graph shown has frequency as the horizontal axis, but what does the vertical axis measure? Could the author of the text please label these axes?

--> Vertical axis should be gain in decibel.

I've improved the caption of the first graph to attempt to address this. ~Kvng (talk) 20:31, 5 June 2022 (UTC)

Fractional Bandwidth

Text no longer in article ~Kvng (talk) 20:31, 5 June 2022 (UTC)

The following discussion is closed. Please do not modify it. Subsequent comments should be made on the appropriate discussion page. No further edits should be made to this discussion.

I believe the second sentence of "A commonly used quantity is fractional bandwidth. This is the center frequency of a device divided by its bandwidth. E.g., a device that has a bandwidth of 2 MHz with center frequency 10 MHz will have a fractional bandwidth of 2/10, or 20%." should read "...This is the bandwidth of a device divided by its center frequency...". This makes the definition in agree with the example in the third sentence.

The discussion above is closed. Please do not modify it. Subsequent comments should be made on the appropriate discussion page. No further edits should be made to this discussion.

Split proposal

Bandwidth (computing) was apparently created ~Kvng (talk) 20:31, 5 June 2022 (UTC)

The following discussion is closed. Please do not modify it. Subsequent comments should be made on the appropriate discussion page. No further edits should be made to this discussion.

Whoever proposed it should say here what they have in mind doing about it. I think it's not a bad idea, if we can agree on sensible boundaries that everyone likes. Dicklyon 06:36, 1 September 2006 (UTC) 

Agreed if we can get some ideas out and about they might be implmented.
Tokyo Michael 17:09, 5 October 2006 (UTC)

Yes, certainly split the page. -Gphoto 17:59, 24 October 2006 (UTC)

  • Oppose. Having thought it over some more, there's not much here. How about expanding on the various meanings, or the application of the concept to the different fields, and see if it gets large or unwieldy. If so, then split it at that time. Dicklyon 05:00, 27 October 2006 (UTC)

I don't know what should be done with the article, but bandwidth as it relates to computers needs to be examined in much greater detail - e.g. the physics behind data transmission, the economics of bandwidth, the engineering involved etc. Perhaps a separate article like Bandwidth (computing) could be created for this, since it could easily dwarf the article. I still think this page should have a general scope though as it does now rather than being a disambiguation page. Richard001 06:12, 10 December 2006 (UTC)

  • Split: Bandwidth means fundementally different things in the analogue and digital spheres, though they both equate approximately to how much data can be stuffed through a media. Would make more sense to make this page a disambiguation page and have separate articles.
  • Split - Bandwith means many different things. I would have this page either be the bits-per-second definition or a disambiguation page listing the bits-per-second meaning, the linear algebra furthest-distance-from-nonzero-to-diagonal definition, and the signal-processing range-of-frequencies definition. Either way, somewhere we should clearly state "Bandwidth has many distinct technical meanings." —Ben FrantzDale (talk) 02:05, 23 January 2008 (UTC)
The discussion above is closed. Please do not modify it. Subsequent comments should be made on the appropriate discussion page. No further edits should be made to this discussion.
Retrieved from "http://en.wiki.x.io/w/index.php?title=Talk:Bandwidth_(signal_processing)/Archive_1&oldid=1158755271"